Amprobe DM-II-PLUS Power-Quality-Recorder Manual de usuario Pagina 26
- Pagina / 194
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
24
Message Description Advices
No parameter se-
lected
A recording has been started without
selecting values to be recorded
Push START/STOP, and se-
lect at least one value from
the MENU
No Phase selected Voltage and/or current harmonics have
been selected and the corresponding
flag has been enabled (HARMONICS
ON) but no phase voltage or current has
been selected
Select at least one phase
voltage and/or current
PASSWORD ERROR The password entered is wrong Insert the password: F1, F4,
F3, F2
PASSWORD OK The password is correct
Please wait The instrument is waiting for the record-
ing to start
Recording The instrument is recording
Too many param More than 63 parameters have been
selected (harmonics included) or more
than 38 parameters with COGENERA-
TION Flag enabled
Deselect parameters
Too many record The quantity of recorded data + Smp
exceeds the maximum allowed (35)
Transfer recordings to a PC
and then clear the instru-
ment memory
ERR: SEQ The Phase Sequence is wrong. Check the Phase Sequence
connection.
ERR: P- The active powers on the right side of
the message are negative
Check if the clamps are
properly connected, unless
co-generation is involved
ERR: SEQ & P- The active powers on the right side of
the message are negative and the Phase
Sequence is wrong.
Check if the clamps are
properly connected / check
the Phase Sequence con-
nection, unless co-genera-
tion is involved
ERR: CONNECTION The Voltage inputs are not connected
correctly.
Check the Voltage connec-
tions (see Physical Connec-
tions, Page X8)
Error Vref A Voltage reference was selected that is
not compatible with voltage input.
Check Voltage Reference
set in RECORDER CONFIG
in MENU
Error1 to Error 5 The instrument memory is damaged. Contact Amprobe for as-
sistance
- DM-II PLUS 1
- Power Quality Recorder 5
- Warnings and Precautions 7
- Instrument: Description 9
- Keyboard: Description 9
- Display: Description 9
- Default Settings 10
- SYSTEM CONNECTIONS 10
- OPERATION 10
- MEASURING PROCEDURES 12
- To Start a Recording 12
- Stop a Recording 12
- Connection with a PC 13
- EVALUATING PARAMETER VALUES 13
- Voltage (Refer to Fig.6) 13
- HARM. Mode (Refer to Fig.7) 13
- WAVE Mode (Refer to Fig.8) 14
- Current (Refer to Fig.9) 14
- Power (Refer to Fig.12) 15
- Energy (Refer to Fig.15) 16
- Recorder Configuration 17
- Warning 21
- Environment 25
- APPENDIX 25
- Messages Displayed 25
- Recordable Parameters Symbols 27
- Réparation 36
- Consignes de sécurité 39
- Mises en garde et précautions 39
- PRÉCAUTIONS ET SÉCURITÉ 39
- Symboles 39
- Clavier : Description 41
- Affichage : Description 41
- Paramètres par défaut 42
- CONNEXIONS DU SYSTEME 43
- FONCTIONNEMENT 43
- TECHNIQUES DE MESURE 44
- Arrêt d’un enregistrement 45
- Connexion avec un PC 45
- DE L’ANALYSEUR) 49
- ENTRETIEN ET RÉPARATION 54
- Avertissement 55
- Environnement 58
- Messages affichés 58
- Reparatur 68
- Netzqualitätsrecorder 69
- Warn- und Vorsichtshinweise: 71
- Messgerät: Beschreibung 73
- Tastatur: Beschreibung 73
- Anzeige: Beschreibung 73
- Standardeinstellungen 74
- SYSTEMVERBINDUNGEN 74
- BEDIENUNG 75
- MESSVERFAHREN 76
- Starten einer Aufzeichnung 76
- Beenden einer Aufzeichnung 77
- Anschluss an einen PC 77
- PARAMETERWERTE UNTERSUCHEN 78
- Spannung (siehe Abb. 6) 78
- HARM.-Modus (siehe Abb. 7) 78
- WAVE-Modus (siehe Abb. 8) 78
- Strom (siehe Abb. 9) 79
- Leistung (siehe Abb. 12) 79
- Energie (siehe Abb. 15) 81
- ANALYZER-SPEICHER 81
- Recorder-Konfiguration 82
- Warnung 86
- TECHNISCHE SPEZIFIKATIONEN 87
- Merkmale 87
- Umgebung 89
- Angezeigte Meldungen 90
- Riparazioni 100
- Avvertenze e precauzioni 103
- + 104
- Descrizione della tastiera 105
- Descrizione del display 105
- Impostazioni predefinite 106
- CONNESSIONI ALL’IMPIANTO 106
- FUNZIONAMENTO 106
- PROCEDURE DI MISURA 108
- Inizio di una registrazione 108
- Arresto di una registrazione 109
- Connessione con un PC 109
- Tensione (vedi Fig. 6) 109
- Modalità WAVE (vedi Fig. 8) 110
- Corrente (vedi Fig. 9) 110
- Potenza (vedi Fig. 12) 111
- Energia (vedi Fig. 15) 112
- Configurazione registratore 113
- MANUTENZIONE E RIPARAZIONI 117
- Attenzione 118
- Ambiente 121
- APPENDICE 121
- Messaggi visualizzati 121
- Reparación 132
- Advertencias y precauciones 135
- Teclado: Descripción 137
- Pantalla: Descripción 137
- Configuración predeterminada 138
- CONEXIONES DEL SISTEMA 138
- FUNCIONAMIENTO 138
- PROCEDIMIENTOS DE MEDICIÓN 140
- Para iniciar un registro 140
- Detener un registro 141
- Conexión con un PC 141
- Tensión (consulte la fig. 6) 141
- Modo WAVE (consulte la fig. 8) 142
- Corriente (consulte la fig. 9) 142
- Potencia (consulte la fig. 12) 143
- Energía (consulte la fig. 15) 144
- MEMORIA DEL ANALIZADOR 144
- Configuración del registrador 145
- Advertencia 149
- Medio ambiente 152
- APÉNDICE 153
- Mensajes en pantalla 153
- Reparation 164
- Symboler 167
- Säkerhetsinformation 167
- Tangentbord: Beskrivning 169
- Teckenfönster: Beskrivning 169
- Standardinställningar 170
- SYSTEMANSLUTNINGAR 170
- Enfassystem (se fig. 2) 170
- MÄTNINGSPROCEDURER 172
- Starta registrering 172
- Under registrering (se fig. 5) 173
- Stoppa registrering 173
- Anslutning med dator 173
- UTVÄRDERA PARAMETERVÄRDEN 173
- Spänning (se fig. 6) 174
- HARM.- läge (se fig. 7) 174
- WAVE-läge (se fig. 8) 174
- Ström (se fig. 9) 174
- Effekt (se fig. 12) 175
- Energi (se fig. 15) 176
- OCH ANALYSATORMINNE 176
- Varning 181
- TEKNISKA DATA 182
- Funktioner 182
- Meddelanden som visas 185
- Visit www.Amprobe.com for 194
- Catalog• 194
- Application notes• 194
- Product specifications• 194
- User manuals• 194
Relacionado con productos y manuales para Instrumentos de medición Amprobe DM-II-PLUS Power-Quality-Recorder
(104 paginas)
(62 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.068 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales