Amprobe DM9C Digital-Multimeter Manual de usuario Pagina 5
- Pagina / 88
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Contents
1 pc. Amprobe DM9C
1 pc. Holster
2 pcs. Test Leads (1ea. red, 1ea. black)
2 pc. Batteries 1.5V, IEC R03
1 pc. Users Manual
Transport and Storage
• Please keep the original packaging for later transport, e.g. for calibration. Any
transport damage due to faulty packaging will be excluded from warranty claims.
• In order to avoid instrument damage, it is advised to remove batteries when not using
the instrument over a certain time period. However, should the instrument be
contaminated by leaking battery cells, you are kindly requested to return it to the
factory for cleaning and inspection.
• Instruments must be stored in dry and closed areas. In the case of an instrument
being transported in extreme temperatures, a recovery time of minimum 2 hours is
required prior to instrument operation.
Safety
• The multimeter has been manufactured and tested to comply with the safety
regulations for electronic measuring equipment contained in IEC61010 and EN
61010, and left the factory in a safe condition. To maintain this condition, the user
must observe the safety instructions contained in this users manual.
• To avoid electric shock, safety measures must be observed when working with
voltages higher than 120 V (60 V) DC or 50 V (25 V) RMS AC. These are the
values of threshold contact voltages given by DIN VDE.
• Before each measurement make sure that the test leads and the instrument are
undamaged.
• Only handle test leads and probes on the grips provided. Avoid touching probes under
any circumstances.
• Measurements in dangerous proximity of electrical installations are only to be
executed when instructed by a responsible electrical specialist, and never alone.
• The relevant safety regulations for electrical plant and equipment must be
observed during all operations.
• The instrument must only be used in the specified ranges.
• Before opening the instrument, it must be disconnected from all circuits.
• Protect the instrument from prolonged exposure to direct sunlight.
3
2526044_Rev2_dm9c.qxd 10/26/06 9:50 AM Page 3
- Contents 3
- Users Manual 3
- Introduction 4
- Transport and Storage 5
- Appropriate Usage 6
- Feature Diagram 6
- Operation 7
- Voltage Measurement 7
- Resistance Measurement 8
- Continuity Test 8
- Diode Test 9
- Current Measurement 9
- Changing the batteries 11
- Fuse replacement 11
- Maintenance 12
- Calibration Interval 12
- Bedienungdsanleitung 17
- DM9C Multimeter 17
- Hinweise: 18
- Einleitung / Lieferumfang 18
- Sicherheitsmaßnahmen 19
- Transport und Lagerung 19
- Bestimmungsgemäße Verwendung 20
- Bedienelemente 20
- Durchführen von Messungen 21
- Spannungsmessung 21
- Widerstandmessung 22
- Durchgangsprüfung 22
- Dioden-Test 23
- Strommessung 23
- Strommessung 400 mA 24
- Strommessung 10 A 24
- Batteriewechsel 25
- Sicherungswechsel 25
- Reinigung 26
- Kalibrierintervall 26
- Reparatur 29
- Mode d’emploi 31
- Introduction/Livraison 32
- Transport et stockage 33
- Mesures de sécurité 33
- Utilisation appropriée 34
- Fonctions et branchements 34
- Réalisation des mesures 35
- Mesure de tension 35
- Mesure de résistance 36
- Mesure de continuité 36
- Mesure de diode 37
- Mesure d´intensité 37
- Mesure d´intensité 400 mA 38
- Mesure d´intensité 10 A 38
- Changement de piles 39
- Changement des fusibles 39
- Entretien 40
- Intervalle de calibrage 40
- Réparation 43
- Contenido 45
- Manual de uso 45
- Instrucciones: 46
- Transporte y almacenamiento 47
- Precauciones 47
- Uso previsto 48
- Elementos y conexiones 48
- Realización de mediciones 49
- Medición de tensión 49
- Medición de resistencia 50
- Prueba de continuad 50
- Prueba de diodos 51
- Medición de corriente 51
- Medición de corriente 400 mA 52
- Medición de corriente 10 A 52
- Reemplazo de baterías 53
- Reemplazo de fusibles 53
- Mantenimiento 54
- Intervalo de calibración 54
- Reparación 57
- Contento 59
- Manuale d’uso 59
- Trasporto e immagazzinaggio 61
- Misure di sicurezza 61
- Uso consentito 62
- Elementi di comando 62
- Esecuzione di misurazioni 63
- Misurazione della tensione 63
- Misurazione della resistenza 64
- Controllo passaggio corrente 64
- Prova diodi 65
- Misurazione di corrente 65
- Sostituzione della batteria 67
- Sostituzione dei fusibili 67
- Manutenzione 68
- Intervallo di calibrazione 68
- Riparazione 71
- Innehåll 73
- Bruksanvisning 73
- Inledning/leveransomfattning 74
- Transport och lagring 75
- Säkerhetsåtgärder 75
- Ändamålsenlig användning 76
- Manöverelement 76
- Genomförande av mätningar 77
- Spänningsmätning 77
- Genomgångsprovning 78
- Motståndsmätning 78
- Diod-test 79
- Strömmätning 79
- Strömmätning 400 mA 80
- Strömmätning 10 A 80
- Batteribyte 81
- Byte av säkringar 81
- Underhåll 82
- Rengöring 82
- Kalibreringsintervall 82
- Reparation 85
Relacionado con productos y manuales para Instrumentos de medición Amprobe DM9C Digital-Multimeter
(90 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.133 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales